#ifndef CYGONCE_HAL_EDB7XXX_H
#define CYGONCE_HAL_EDB7XXX_H

/*=============================================================================
//
//      hal_edb7xxx.h
//
//      HAL Support for Kernel Diagnostic Routines
//
//=============================================================================
//####COPYRIGHTBEGIN####
//                                                                          
// -------------------------------------------                              
// The contents of this file are subject to the Red Hat eCos Public License 
// Version 1.1 (the "License"); you may not use this file except in         
// compliance with the License.  You may obtain a copy of the License at    
// http://www.redhat.com/                                                   
//                                                                          
// Software distributed under the License is distributed on an "AS IS"      
// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the 
// License for the specific language governing rights and limitations under 
// the License.                                                             
//                                                                          
// The Original Code is eCos - Embedded Configurable Operating System,      
// released September 30, 1998.                                             
//                                                                          
// The Initial Developer of the Original Code is Red Hat.                   
// Portions created by Red Hat are                                          
// Copyright (C) 1998, 1999, 2000 Red Hat, Inc.                             
// All Rights Reserved.                                                     
// -------------------------------------------                              
//                                                                          
//####COPYRIGHTEND####
//=============================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):    gthomas
// Contributors: gthomas
// Date:         1999-04-19
// Purpose:      Cirrus Logic EDB7XXX hardware description
// Description:
// Usage:        #include <cyg/hal/hal_edb7xxx.h>
//
//####DESCRIPTIONEND####
//
//===========================================================================*/

// Note: these defintions match the documentation, thus no attempt is made
// to sanitize (mangle) the names.  Also, care should be taken to keep this
// clean for use in assembly code (no "C" constructs).

#define PADR    0x80000000 // Port A data register
#define PBDR    0x80000001 // Port B data register
#define PDDR    0x80000003 // Port D data register
#define PADDR   0x80000040 // Port A data direction register
#define PBDDR   0x80000041 // Port B data direction register
#define PDDDR   0x80000043 // Port D data direction register
#define PEDR    0x80000080 // Port E data register
#define PEDDR   0x800000C0 // Port E data direction register

#define SYSCON1 0x80000100 // System control register #1
#define SYSCON1_KBD_CTL     0xF // Keyboard scan - mask
#define SYSCON1_KBD_HIGH      0 // Keyboard scan - all columns high
#define SYSCON1_KBD_LOW       1 // Keyboard scan - all columns low
#define SYSCON1_KBD_TRISTATE  2 // Keyboard scan - all columns tri-state
#define SYSCON1_KBD_COL(n) (n+8)// Keyboard scan - select column 'n'
#define SYSCON1_TC1M    (1<<4)  // Timer/counter #1 - prescale mode
#define SYSCON1_TC1S    (1<<5)  // Timer/counter #1 - source (1=512KHz,0=2KHz)
#define SYSCON1_TC2M    (1<<6)  // Timer/counter #2 - prescale mode
#define SYSCON1_TC2S    (1<<7)  // Timer/counter #2 - source (1=512KHz,0=2KHz)
#define SYSCON1_UART1EN (1<<8)  // UART #1 enable
#define SYSCON1_BZTOG   (1<<9)  // Buzzer bit
#define SYSCON1_BZMOD   (1<<10) // Buzzer mode (0=direct,1=TC1)
#define SYSCON1_DBGEN   (1<<11) // Enable debug mode
#define SYSCON1_LCDEN   (1<<12) // Enable LCD
#define SYSCON1_CDENTX  (1<<13) // Enable Tx on CODEC
#define SYSCON1_CDENRX  (1<<14) // Enable Rx on CODEC
#define SYSCON1_SIREN   (1<<15) // Enable SIR protocol on UART #1
#define SYSCON1_ADCKSEL (3<<16) // Microwire clock
#define SYSCON1_ADC_CLOCK_4kHZ    (0<<16)
#define SYSCON1_ADC_CLOCK_16kHZ   (1<<16)
#define SYSCON1_ADC_CLOCK_64kHZ   (2<<16)
#define SYSCON1_ADC_CLOCK_128kHZ  (3<<16)
#define SYSCON1_EXCKEN  (1<<18) // External expansion clock enable
#define SYSCON1_WAKEDIS (1<<19) // Disable wakeup from snooze (do not disturb)
#define SYSCON1_IRTXM   (1<<20) // IrDA Tx mode

#define SYSCON2 0x80001100 // System control register #2
#define SYSCON2_SERSEL  (1<<0)  // 0=master/slave SSI, 1=CODEC
#define SYSCON2_KBD6    (1<<1)  // 0=8 bit keyboard, 1=6 bit
#define SYSCON2_DRAMSZ  (1<<2)  // DRAM width 0=32, 1=16
#define SYSCON2_KBWEN   (1<<3)  // 1=allow wake up from keyboard
#define SYSCON2_SS2TXEN (1<<4)  // Enable Tx on SS2
#define SYSCON2_PCMCIA1 (1<<5)  // Enable PCMCIA slot #1
#define SYSCON2_PCMCIA2 (1<<6)  // Enable PCMCIA slot #2
#define SYSCON2_SS2RXEN (1<<7)  // Enable Rx on SS2
#define SYSCON2_UART2EN (1<<8)  // Enable UART #2
#define SYSCON2_SS2MAEN (1<<9)  // Enable master mode on SS2
#define SYSCON2_SNZPOL  (1<<10) // Polarity of LCD during snooze
#define SYSCON2_LCDSNZE (1<<11)
#define SYSCON2_OSTB    (1<<12) // Operating system timing 0=512KHz, 1=500KHz
#define SYSCON2_CLKENSL (1<<13) // Source of run/clken signal 0=CLKEN, 1=RUN
#define SYSCON2_BUZFREQ (1<<14) // Buzzer frequency 0=timer, 1=fixed PLL/xtal

#define SYSCON3 0x80002200 // System control #3
#define SYSCON3_ADCCON    (1<<0) // ADC enable
#define SYSCON3_CLKCTL(n) (n<<1) // Processor block speed ((n+1)*18.432)MHz

#define SYSFLG1 0x80000140 // System flags #1
#define SYSFLG1_MCDR     (1<<0) // Media changed - direct read
#define SYSFLG1_DCDET    (1<<1) // 0=mains power, 1=battery
#define SYSFLG1_WUDR     (1<<2) // Wakeup direct
#define SYSFLG1_WUON     (1<<3) // Woken up
#define SYSFLG1_DID      (0xF<<4) // Display ID
#define SYSFLG1_CTS      (1<<8) // UART1 CTS
#define SYSFLG1_DSR      (1<<9) // UART1 DSR
#define SYSFLG1_DCD      (1<<10) // UART1 DCD
#define SYSFLG1_UBUSY1   (1<<11) // UART1 Tx busy
#define SYSFLG1_NBFLG    (1<<12) // New battery flag
#define SYSFLG1_RSTFLG   (1<<13) // Reset (button) flag
#define SYSFLG1_PFFLG    (1<<14) // Power fail flag
#define SYSFLG1_CLDFLG   (1<<15) // Cold start flag
#define SYSFLG1_RTCDIV   (0x3F<<16) // Real time clock divider (counter)
#define SYSFLG1_URXFE1   (1<<22) // UART1 Rx FIFO empty
#define SYSFLG1_UTXFF1   (1<<23) // UART1 Tx FIFO full
#define SYSFLG1_CRXFE    (1<<24) // CODEC Rx FIFO empty
#define SYSFLG1_CTXFF    (1<<25) // CODEC Tx FIFO full
#define SYSFLG1_SSIBUSY  (1<<26) // Synchronous serial interface busy
#define SYSFLG1_BOOTBITS (3<<27) // Boot mode (0=32,1=8,2=16,3=XX)
#define SYSFLG1_ID       (1<<29) // ID=1
#define SYSFLG1_VERID    (3<<30) // Board version

#define SYSFLG2 0x80001140 // System flags #2

#define INTSR1  0x80000240 // Interrupt status register #1
#define INTSR1_EXTFIQ  (1<<0)  // External fast interrupt
#define INTSR1_BLINT   (1<<1)  // Battery low interrupt
#define INTSR1_WEINT   (1<<2)  // Watchdog expired interrupt
#define INTSR1_MCINT   (1<<3)  // Media changed interrupt
#define INTSR1_CSINT   (1<<4)  // CODEC sound interrupt
#define INTSR1_EINT1   (1<<5)  // External interrupt #1
#define INTSR1_EINT2   (1<<6)  // External interrupt #2
#define INTSR1_EINT3   (1<<7)  // External interrupt #3
#define INTSR1_TC1OI   (1<<8)  // Timer/counter #1 underflow
#define INTSR1_TC2OI   (1<<9)  // Timer/counter #2 underflow
#define INTSR1_RTCMI   (1<<10) // Real time clock match
#define INTSR1_TINT    (1<<11) // 64Hz tick
#define INTSR1_UTXINT1 (1<<12) // UART1 Tx interrupt
#define INTSR1_URXINT1 (1<<13) // UART1 Rx interrupt
#define INTSR1_UMSINT  (1<<14) // UART1 modem line change
#define INTSR1_SSEOTI  (1<<15) // Synchronous serial end of transfer
#define INTMR1  0x80000280 // Interrupt mask register #1

#define INTSR2  0x80001240 // Interrupt status #2
#define INTSR2_KBDINT  (1<<0)  // Keyboard interrupt
#define INTSR2_SS2RX   (1<<1)  // Synchronous serial #2 Rx
#define INTSR2_SS2TX   (1<<2)  // Synchronous serial #2 Tx
#define INTSR2_UTXINT2 (1<<12) // UART #2 Tx interrupt
#define INTSR2_URXINT2 (1<<13) // UART #2 Rx interrupt
#define INTMR2  0x80001280 // Interrupt mask #2

#define INTSR3  0x80002240 // Interrupt status #3
#if defined(__EDB7211)
#define INTSR3_MCPINT (1<<0) // MCP interrupt
#endif
#define INTMR3  0x80002280 // Interrupt mask #3

#define UARTDR1 0x80000480 // UART #1 data register
#define UARTDR2 0x80001480 // UART #2 data register
#define UBLCR1  0x800004C0 // UART #1 baud rate / line control
#define UBLCR2  0x800014C0 // UART #2 baud rate / line control
#define UBLCR_BRDV    0xFFF   // Baud rate
#define UBLCR_BREAK   (1<<12) // Generate break signal
#define UBLCR_PRTEN   (1<<13) // Enable parity
#define UBLCR_EVENPRT (1<<14) // 1=even parity, 0=odd
#define UBLCR_XSTOP   (1<<15) // 0=1 stop bit, 1=2 stop bits
#define UBLCR_FIFOEN  (1<<16) // Enable Tx/Rx FIFOs
#define UBLCR_WRDLEN  (3<<17) // Word (character) length field
#define UBLCR_WRDLEN5 (0<<17)
#define UBLCR_WRDLEN6 (1<<17)
#define UBLCR_WRDLEN7 (2<<17)
#define UBLCR_WRDLEN8 (3<<17)
#define UART_DIVISOR  230400
#define UART_BITRATE(baud) ((UART_DIVISOR/(baud))-1)

#define MEMCFG1 0x80000180 // Memory configuration register #1
#define MEMCFG2 0x800001C0 // Memory configuration register #2

#define DRFPR   0x80000200 // DRAM refresh period

#define LCDCON                0x800002C0  // LDC control
#define LCDCON_BUFSIZ         0x00001FFF  // Video buffer size
#define LCDCON_BUFSIZ_S       0           // Position of buffer size
#define LCDCON_LINE_LENGTH    0x0007E000  // Line length
#define LCDCON_LINE_LENGTH_S  13          // Position of line length
#define LCDCON_PIX_PRESCALE   0x01F80000  // Pixel prescale value
#define LCDCON_PIX_PRESCALE_S 19          // Position of prescale value
#define LCDCON_AC_PRESCALE    0x3E000000  // LCD AC bias frequency
#define LCDCON_AC_PRESCALE_S  25          // Position to AC bias
#define LCDCON_GSEN           0x40000000  // Enable greyscale
#define LCDCON_GSMD           0x80000000  // Greyscale mode
                                          // 00 - 1bpp, 01 - 2bpp, 11 - 4 bpp

#define TC1D    0x80000300 // Timer/Counter #1 register
#define TC2D    0x80000340 // Timer/Counter #2 register
#define RTCDR   0x80000380 // Real time clock data register
#define RTCMR   0x800003C0 // Real time clock match register

#define PMPCON  0x80000400 // DC-DC pump control

#define CODR    0x80000440 // CODEC data register

#define SYNCIO  0x80000500 // Synchronous I/O data register

#define PALLSW  0x80000540 // LCD palette - LSW (Pixel values 0..7)
#define PALMSW  0x80000580 // LCD palette - MSW (Pixel values 8..15)

#define STFCLR  0x800005C0 // Clear startup reason flags
#define BLEOI   0x80000600 // Clear battery low interrupt
#define MCEOI   0x80000640 // Clear media changed interrupt
#define TEOI    0x80000680 // Clear tick/watchdog interrupt
#define TC1EOI  0x800006C0 // Clear timer/counter #1 interrupt
#define TC2EOI  0x80000700 // Clear timer/counter #2 interrupt
#define RTCEOI  0x80000740 // Clear real time clock interrupt
#define UMSEOI  0x80000780 // Clear UART modem status change interrupt
#define COEOI   0x800007C0 // Clear CODEC sound interrupt

#define HALT    0x80000800 // Enter 'idle' state
#define STDBY   0x80000840 // Enter 'standby' state

#define FRBADDR 0x80001000 // LCD frame buffer start

#define SNZDISP 0x800012C0 // Snooze display size

#define SS2DR   0x80001500 // Master/slave SSI2 register

#define SRXEOF  0x80001600 // Clear Rx FIFO overflow flag
#define SS2POP  0x800016C0 // Pop SSI2 residual byte into FIFO

#define KBDEOI  0x80001700 // Clear keyboard interrupt

#define SNOOZE  0x80001800 // Enter 'snooze' state

#if defined(__EDB7211)
#define MCCR    0x80002000 // MCP control register
#define MCDR0   0x80002040 // MCP data register #0
#define MCDR1   0x80002080 // MCP data register #1
#define MCDR2   0x800020C0 // MCP data register #2
#define MCSR    0x80002100 // MCP status register
#endif


#define LEDFLSH 0x800022C0 // LED flash control
#define LEDFLSH_ENABLE      (1<<6)      // LED enabled
#define LEDFLSH_DUTY(n)     ((n-1)<<2)  // LED on ratio
#define LEDFLSH_PERIOD(n)   (n-1)       // LED active time (1..4)

#define KBD_PORT 0x30010000 // Extra 8 bits of keyboard data

/*---------------------------------------------------------------------------*/
/* end of hal_edb7xxx.h                                                         */
#endif /* CYGONCE_HAL_EDB7XXX_H */