2001-10-16  Jesper Skov  <jskov@redhat.com>

	* include/dp83902a.h: Removed hardwired buffer
	allocation. Replaced with per-device configuration.
	* src/if_dp83902a.c: Same.

2001-10-15  Jesper Skov  <jskov@redhat.com>

	* include/dp83902a.h: Added new page allocation layout.

2001-10-12  Gary Thomas  <gthomas@redhat.com>

	* src/if_dp83902a.c: Leave out interrupt code - not needed in 
	non-NET configurations.

2001-10-10  Gary Thomas  <gthomas@redhat.com>

	* src/if_dp83902a.c: 
	* include/dp83902a.h: More flexible setup.  Chip reset address is
	now in device data, along with changes to the PLF reset functions.
	Also, a new PLF init function can be defined which allows the driver
	to work in a PCI enviroment (addresses unknown at compile time).

2001-09-12  Jesper Skov  <jskov@redhat.com>

	* src/if_dp83902a.c: Apply a little more DMA magic.

2001-08-25  Gary Thomas  <gthomas@redhat.com>

	* include/dp83902a.h (DP_DATAPORT): Add - used by ESA discovery
	on SC/LPE card.

2001-06-21  Jesper Skov  <jskov@redhat.com>

	* src/if_dp83902a.c: Fix various build problems when net package
	is included.

2001-06-16  Jesper Skov  <jskov@redhat.com>

	* src/if_dp83902a.c (dp83902a_poll): Ignore spurious Tx events.

2001-06-15  Jesper Skov  <jskov@redhat.com>

	* src/if_dp83902a.c: Added crude CR race check. Use plf interrupt
	clear to allow for CF driver to use this driver. Cleaned up debug
	output some.
	(dp83902a_send): Added some magic delays to get driver working on
	some (apparently) broken boards.

	* src/dp83902a.h: Moved..
	* include/dp83902a.h: to here. Moved macro definitions here from
	the src file.

	* cdl/ns_dp83902a_eth_drivers.cdl: Export header file.

2001-06-14  Jesper Skov  <jskov@redhat.com>

	* src/if_dp83902a.c: Added some more debug info.

	* src/dp83902a.h: Added 16bit/BE macros (untested).

	* src/if_dp83902a.c: Add some debug code, fix endian issue. Proper
	handling of odd-length reads in 16bit mode.

2001-06-13  Jesper Skov  <jskov@redhat.com>

	* src/if_dp83902a.c: Assume LE ordering of read header data.

	* src/dp83902a.h: BE/LE versions of data IO. Define proper DCR
	init value depending on data access width.

	* Cloned from DP8390 driver.

//===========================================================================
//####COPYRIGHTBEGIN####
//                                                                          
// -------------------------------------------                              
// The contents of this file are subject to the Red Hat eCos Public License 
// Version 1.1 (the "License"); you may not use this file except in         
// compliance with the License.  You may obtain a copy of the License at    
// http://www.redhat.com/                                                   
//                                                                          
// Software distributed under the License is distributed on an "AS IS"      
// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the 
// License for the specific language governing rights and limitations under 
// the License.                                                             
//                                                                          
// The Original Code is eCos - Embedded Configurable Operating System,      
// released September 30, 1998.                                             
//                                                                          
// The Initial Developer of the Original Code is Red Hat.                   
// Portions created by Red Hat are                                          
// Copyright (C) 1998, 1999, 2000, 2001 Red Hat, Inc.
// All Rights Reserved.                                                     
// -------------------------------------------                              
//                                                                          
//####COPYRIGHTEND####
//===========================================================================