new file mode 100644
--- /dev/null
+++ b/packages/devs/serial/arm/aeb/current/src/aeb_serial.h
@@ -0,0 +1,154 @@
+#ifndef CYGONCE_ARM_AEB_SERIAL_H
+#define CYGONCE_ARM_AEB_SERIAL_H
+
+// ====================================================================
+//
+//      aeb_serial.h
+//
+//      Device I/O - Description of ARM AEB-1 serial hardware
+//
+// ====================================================================
+//####COPYRIGHTBEGIN####
+//                                                                          
+// -------------------------------------------                              
+// The contents of this file are subject to the Red Hat eCos Public License 
+// Version 1.1 (the "License"); you may not use this file except in         
+// compliance with the License.  You may obtain a copy of the License at    
+// http://www.redhat.com/                                                   
+//                                                                          
+// Software distributed under the License is distributed on an "AS IS"      
+// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the 
+// License for the specific language governing rights and limitations under 
+// the License.                                                             
+//                                                                          
+// The Original Code is eCos - Embedded Configurable Operating System,      
+// released September 30, 1998.                                             
+//                                                                          
+// The Initial Developer of the Original Code is Red Hat.                   
+// Portions created by Red Hat are                                          
+// Copyright (C) 1998, 1999, 2000 Red Hat, Inc.                             
+// All Rights Reserved.                                                     
+// -------------------------------------------                              
+//                                                                          
+//####COPYRIGHTEND####
+// ====================================================================
+//#####DESCRIPTIONBEGIN####
+//
+// Author(s):           gthomas
+// Contributors:        gthomas
+// Date:        1999-02-04
+// Purpose:     Internal interfaces for serial I/O drivers
+// Description:
+//
+//####DESCRIPTIONEND####
+//
+// ====================================================================
+
+// Description of serial ports on ARM AEB-1
+
+struct serial_port {
+    unsigned char _byte[32];
+};
+
+#define REG(n) _byte[n*4]
+
+// Receive control registers
+#define REG_RHR REG(0)    // Receive holding register
+#define REG_ISR REG(2)    // Interrupt status register
+#define REG_LSR REG(5)    // Line status register
+#define REG_MSR REG(6)    // Modem status register
+#define REG_SCR REG(7)    // Scratch register
+
+// Transmit control registers
+#define REG_THR REG(0)    // Transmit holding register
+#define REG_IER REG(1)    // Interrupt enable register
+#define REG_FCR REG(2)    // FIFO control register
+#define REG_LCR REG(3)    // Line control register
+#define REG_MCR REG(4)    // Modem control register
+#define REG_LDL REG(0)    // LSB of baud rate
+#define REG_MDL REG(1)    // MSB of baud rate
+
+// Interrupt Enable Register
+#define IER_RCV 0x01
+#define IER_XMT 0x02
+#define IER_LS  0x04
+#define IER_MS  0x08
+
+// Line Control Register
+#define LCR_WL5 0x00    // Word length
+#define LCR_WL6 0x01
+#define LCR_WL7 0x02
+#define LCR_WL8 0x03
+#define LCR_SB1 0x00    // Number of stop bits
+#define LCR_SB1_5 0x04  // 1.5 -> only valid with 5 bit words
+#define LCR_SB2 0x04
+#define LCR_PN  0x00    // Parity mode - none
+#define LCR_PE  0x0C    // Parity mode - even
+#define LCR_PO  0x08    // Parity mode - odd
+#define LCR_PM  0x28    // Forced "mark" parity
+#define LCR_PS  0x38    // Forced "space" parity
+#define LCR_DL  0x80    // Enable baud rate latch
+
+// Line Status Register
+#define LSR_RSR 0x01
+#define LSR_THE 0x20
+
+// Modem Control Register
+#define MCR_DTR 0x01
+#define MCR_RTS 0x02
+#define MCR_INT 0x08   // Enable interrupts
+
+// Interrupt status register
+#define ISR_Tx  0x02
+#define ISR_Rx  0x04
+
+static unsigned char select_word_length[] = {
+    LCR_WL5,    // 5 bits / word (char)
+    LCR_WL6,
+    LCR_WL7,
+    LCR_WL8
+};
+
+static unsigned char select_stop_bits[] = {
+    0,
+    LCR_SB1,    // 1 stop bit
+    LCR_SB1_5,  // 1.5 stop bit
+    LCR_SB2     // 2 stop bits
+};
+
+static unsigned char select_parity[] = {
+    LCR_PN,     // No parity
+    LCR_PE,     // Even parity
+    LCR_PO,     // Odd parity
+    LCR_PM,     // Mark parity
+    LCR_PS,     // Space parity
+};
+
+// Baud rate values, based on raw 24MHz clock
+
+static unsigned short select_baud[] = {
+           0,  // Unused
+     10000*3,  // 50
+      6667*3,  // 75
+      4545*3,  // 110
+      3717*3,  // 134.5
+      3333*3,  // 150
+           0,  // 200
+      1667*3,  // 300
+       833*3,  // 600
+       417*3,  // 1200
+       277*3,  // 1800
+       208*3,  // 2400
+       139*3,  // 3600
+       104*3,  // 4800
+        69*3,  // 7200
+        52*3,  // 9600
+    (69*3)/2,  // 14400
+        26*3,  // 19200
+        13*3,  // 38400
+           0,  // 57600
+           0,  // 115200
+           0,  // 230400
+};
+
+#endif // CYGONCE_ARM_AEB_SERIAL_H